Retrofit or Replace? Adding Steam Recovery to an Existing HCl Furnace (2026 Numbers)
Published: November 2026 | By Fareast Engineering Team
Retrofitting steam recovery to an existing HCl furnace costs 45–55% of a new unit — $280,000 to $450,000 at 100 TPD, against $600,000–900,000 for a greenfield package. The saving is real. So is the catch: the furnace body usually has to be replaced anyway.
That is the part most retrofit proposals gloss over. You cannot bolt a steam drum onto a water-jacketed furnace and call it heat recovery. This article sets out what can genuinely be reused, what the shutdown really costs, and the four conditions under which replacing the unit is the cheaper answer.
Fareast builds and rebuilds graphite HCl synthesis units in Nantong, and has quoted both greenfield and in-situ replacement scopes from the same works since 1996. The project figures below are published Chinese installations, converted at RMB 7.1 to the dollar.
How Much Does a Retrofit Cost Compared With a New Unit?
At 100 TPD, the graphite synthesis furnace retrofit steam recovery investment lands at $280,000–450,000 — roughly half of a new package, because civil works, the absorption train, the building and the gas headers all stay.
The best public benchmark is an Inner Mongolia chlor-alkali site that replaced twelve water-jacketed graphite furnaces with nine steam-generating units, 150 t/d each, producing 1.0 MPaG steam. Total investment: RMB 35 million, about RMB 3.9 million per new furnace including demolition and reinstallation. Against a greenfield 150 TPD package, that is 47–66% — the same ratio you get by arithmetic at 100 TPD. Capacity did not change; the absorption train was kept.
What a retrofit actually buys:
• A new pressure-rated furnace body and shell — unavoidable, the old water jacket cannot take boiler feedwater
• The steam drum, evaporator section, boiler feed pump and pressure control
• Demolition, rigging and reconnection to existing nozzles
• A DCS and interlock upgrade, if the old unit ran on relay logic
• Reused: absorber, tail gas scrubber, foundations, building, HCl headers, storage
The arithmetic looks better than it is until you price the shutdown. A single 100 TPD unit takes three to five weeks to cut out, re-set and commission. At 100 t/d that is 2,100–3,500 tonnes of HCl not produced; at a $60 per tonne contribution margin, $126,000–210,000 of lost margin — half the retrofit budget again, and invisible in most quotations.
✅ Bottom line: Budget the retrofit at half a new unit, then add the shutdown window as a separate line. Projects that skip it approve $350,000 and spend $500,000.
When Is Replacing the Furnace the Cheaper Answer?
Replace rather than retrofit in four cases: the body is past eight years, you need more than 15–20% extra capacity, the unit fails a safety or emissions review, or it is still steel.
Take them in order, because the first decides the other three. Quoted service life for a graphite synthesis unit is eight years and up; once a body is near that, a retrofit is paying twice for the same shell.
Capacity is the second. An HCl synthesis furnace revamp capacity expansion existing unit is often the real reason the project exists, and the shell diameter is the binding constraint. If you want 20% more HCl, a new body sized for it costs little more than a like-for-like one — which is why capacity projects usually skip the retrofit question entirely.
Compliance is the third, and it is where steel furnaces surface. One 2023 project replaced four steel synthesis furnaces installed in the 1950s and 1960s, with no SIS and no DCS, for RMB 13 million. That is not a heat-recovery project; it is a safety project that happens to produce steam.
Ask for that scope split three ways — furnace, absorption, automation, at about RMB 3.25 million per unit in that project. Bundled steel-to-graphite offers hide the fact that half the old steel synthesis furnace upgrade to graphite furnace cost buys purity and safety rather than steam, which matters when you are defending the project to a finance committee that only approved an energy case.
The fourth is water-side history. Repeated impregnation failures, tube-side leaks or a shell that has been re-sealed twice are the body telling you it is finished. A retrofit will not fix any of them.
Execution matters as much as the decision. The Inner Mongolia project ran in three phases over three years, two furnaces at a time, ending with eight running and one standby — capacity never dropped. A five-unit steel conversion elsewhere took seven months as an EPC scope and repaid in six months. Fareast pre-assembles and factory-tests the new body before the old one comes out, so the site window is rigging and reconnection, not fabrication. Phase it that way and the graphite synthesis furnace retrofit steam recovery investment stops competing with production for the same window.
✅ Bottom line: Retrofit when the body has life left and capacity is fixed. Replace when the body is near eight years or the plant needs more HCl — the price difference is smaller than the second shutdown.
Frequently Asked Questions
Q: Can a steam drum be added to an existing water-cooled furnace without replacing the body?
A: Not on a water-jacketed unit. The jacket is a cooling passage, not a pressure part; boiler feedwater at 0.6–1.0 MPa needs a shell and graphite wall designed for it, with spring compensation for the differential expansion. That is why the graphite synthesis furnace retrofit steam recovery investment always includes a new body. Low-grade alternatives exist — a gas cooler on the outlet or a hot-water loop off the absorber — but they recover maybe a third as much and rarely justify the piping.
Q: How do you retrofit without shutting the plant down?
A: You do not — you shorten the window and you phase it. Pre-assemble and factory-test the new body, pre-fabricate every spool to the existing nozzle positions, and keep one unit as standby so the line keeps running on n−1. Typical site window for one 100 TPD unit is three to five weeks, including water test and commissioning. Plants with four or more units often replace two per turnaround and never lose nameplate capacity — the same planning logic that governs an HCl synthesis furnace revamp capacity expansion existing unit, where the standby unit does the work while the new body goes in.
Q: What should a supplier deliver for a retrofit scope?
A: A dimensional survey of the existing installation, not just a datasheet. Nozzle elevations, header sizes, foundation bolt pattern and the absorber inlet all constrain the new body. If the old unit is steel, insist the old steel synthesis furnace upgrade to graphite furnace cost arrives as its own line rather than folded into the furnace price. Ask for the heat and mass balance, the steam guarantee at three load points, and the pressure-vessel file. Nantong Fareast Chemical Equipment Co., Ltd. holds an A4 non-metallic pressure vessel manufacturing licence (2023), has been ISO 9001 certified since 2007, and took part in drafting two national standards for impermeable graphite equipment effective July 2026. Fareast works from site survey drawings and quotes custom and OEM retrofit scopes, whether the original unit was ours or not.
Send photographs, the nameplate data and four dimensions — shell height, nozzle elevations, absorber inlet and foundation bolt circle — to Fareast, and you receive a retrofit-versus-replace comparison with both paybacks in your own currency within five working days. No charge, no obligation. Factory-direct pricing from a China manufacturer that has rebuilt units it did not originally build.
www.fe-graphite.com
Nantong Fareast Chemical Equipment Co. LTD